ID 膨胀抓持器系列
• 创新性气动操作手新理念。
• 向下移动 (MFD) 或向上移动 (MFU)。
• 弹性部件可以是硅氧烷或 EPDM。
• 抓手直径为 8 至 85 毫米。
• 可选鼻形锥体用于对中。
• 可选接近磁性传感器。
• 配有几个安装附件。
ID expansion grippers series
• New concept for innovative air hands.
• Downward movement (MFD), or upward movement (MFU).
• The elastic part can be in Silicone or EPDM.
• Grip diameters from 8 to 85 mm.
• Optional nose cones for centering.
• Optional proximity magnetic sensors.
• Several mounting accessories.
编程单个SB8F
在对传感器盒进行编程之前,请确保有线输入处于所需配置(开/关)以启用输出。按下AUTOSET按钮并按住3秒钟,直到READING红灯开始闪烁,然后松开。红灯(READING)闪烁表示微处理器正在读取和存储全部输入的状态。然后红灯熄灭,启用了输出。黄灯(STORED)指示启用输出。
Before programming the sensor box, make sure that the wired inputs are in the confguration (ON/OFF) desired to enable the output. Press the AUTOSET button and hold it down for 3 seconds until the READING red light starts fashing, then release it.The red light (READING) fashing indicates that the microprocessor is reading and storing the state of all the inputs. Then the red light goes off and the output is enabled. Output enabling is indicated by the yellow light (STORED).
配置和指标
•S1:实现选择输出信号的类型,PNP(P/2)或NPN(N)。
•S2:分别根据NPN或PNP选择(通过S1)实现选择内部PULLUP(PU)或PULL-DOWN(PD)电阻器。
•L1:通电时为绿色。
•L2:当常闭系列输出切换时为琥珀色(例如:全部触点打开)。
•L3:当切换常开系列时琥珀色(例如:全部触点闭合)。
•S1: enables the selection of the type of output signal, PNP(P/2) or NPN (N).
•S2: enables the selection of internal PULL-UP (PU) or PULLDOWN(PD) resistors depending on the NPN or PNP selection(via S1), respectively.
•L1: green when powered.
•L2: amber when the NC series output is switched (e.g. allcontacts open).
•L3: amber when the NO series is switched (e.g. all contactsclosed).
双钳口自动对准平行i气动钳夹 (SX系列)
•双动作 (可按需关闭)。
•高夹紧力。
•防护等级为IP67。
•列柱向上采用双层O型圈设计。
•适用于恶劣的环境。
•可选的磁传感器。
•FDA-H1 食品级润滑脂
•Double acting (normally closed on request).
•High gripping force.
•Protection class: IP67.
•Double O-Ring sealing on the columns.
•Suitable for harsh environments.
•Optional magnetic sensors.
•FDA-H1 food-grade grease.
以上信息由专业从事旋转夹钳装置的吉玛泰克于2025/3/24 13:27:18发布
转载请注明来源:http://alashan.mf1288.com/jmtkzdh-2850619876.html